.jpg)
What you need
Besides the product, you need three things to mount bathroom accessories with 3M tape without drilling: a surface cleaning wipe, a level and a marker.
1. Find the best surface
Before ordering your new interior details, find a place where you want to install them. This gives you a chance to choose the best surface for the product, helping it stay secure and last longer. But what makes a good surface? The best surfaces: Tile and lacquered or veneered boards.
Surfaces to avoid: Wallpaper or wall fabric, uneven or rough surfaces, and bathroom wallpaper.
Tile is one of the best surfaces for the product because it is fixed to the wall and often has a glossy, smooth surface that helps the 3M tape adhere well. The same applies to lacquered and veneered boards. These surfaces are also unlikely to be damaged if you decide to remove or replace the details in the future.
If you attach the products to a wall covered with wallpaper or wall fabric, both the product and the covering may come loose when weight is placed on the product. On rough or uneven surfaces, the tape cannot make contact with the entire surface, reducing its grip. Bathroom wallpaper also tends to bulge, making it harder for the tape to adhere.
2. Positioning bathroom accessories
Decide where you want your accessories to go, then use a level or another tool to make sure the products are mounted straight. Mark the position with a marker just outside the edge of the product, so the mark remains visible once the product is in place. This is especially important when mounting towel bars and shelves. If you want to mount the product across multiple tiles, check that the tiles are level and at the same angle, so the weight is distributed evenly - this will give you the best possible results and durability.
We do not recommend mounting products over grout.
For more tips on where to position your bathroom accessories, click here.
3. Cleaning the surface
Thoroughly clean the surface inside the marks with a surface cleaning wipe to remove dirt, grease and other unwanted particles. Cleaning the surface gives the product the best conditions for optimal adhesion.
4. Installing self-adhesive bathroom accessories
1. Remove the protective film
2. Place the product where you want it on the cleaned surface, then press it down with even pressure for about 10 seconds.
5. Allow to cure for at least 24 hours
1. For the best adhesion, we recommend letting the adhesive cure for at least 24 hours before placing any weight on the product.
2. After 24 hours, the product is ready to use!
Find your new bathroom accessories
Once you have found the ideal surface and location for your new accessories, it’s time to find inspiration and choose your new favorites! You can find our bathroom accessories in the menu. Once in the category, you can filter by color/material, product type or a particular product range. We have a wide selection of products that attach with self-adhesive tape, including hooks, toilet paper holders, shelves, towel holders and soap dispenser holders. Frequently asked questions about mounting with 3M tape
How do I install bathroom accessories without drilling?
With 3M tape. Choose a smooth, clean surface, such as tile or lacquered or veneered boards. Mark the position with a spirit level and marker, clean the surface, remove the protective film and press the product firmly and evenly into place for about 10 seconds. Then let the adhesive cure for at least 24 hours before putting any weight on the product.
Which side of the 3M tape goes against the wall?
On our products, the tape is already attached to the back. Simply peel off the protective film and press the product onto the clean surface, and the correct side will be against the wall.
Can I apply 3M tape over grout, wallpaper or an uneven surface?
We don't recommend it. The tape adheres best to smooth, hard surfaces. Grout, wallpaper, wet-room wallpaper and rough surfaces prevent the tape from making full contact, and the product may come loose when weight is placed on it.
How long should I wait before using the product?
Let the adhesive cure for at least 24 hours before putting any weight on the product. After that, it's ready to use.
Can I put the shower shelf in the shower?
Absolutely! It's perfect in the shower for shampoo, conditioner and soap. You can also place it elsewhere in the bathroom for a little extra storage or as a decorative spot for scented candles or perfumes.
Is the shower shelf water-resistant?
Yes, it is. We recommend not installing the shower shelf over a grout line, as water could get behind the shelf and affect how well it adheres.
Where can I put a soap dispenser holder?
Almost anywhere you like! In the shower, by the sink or why not in the kitchen for soap and dishwashing liquid? There are plenty of ways to use it!
How big is the hole for the soap dispenser?
The hole is 28 mm in diameter, which is the standard size for pump bottles. It would be ideal if all pump bottles were the same size, but unfortunately they aren't.
How do I remove the product without damaging the wall?
Warm the tape with a hair dryer to help it release more easily. Alternatively, use fishing line to work behind the product. Find more tips in our guide to removing self-adhesive bathroom products from the wall.
Do you have extra tape for your 3M products?
Unfortunately, we don't currently sell spare tape on our website. We hope to have a solution for this in the future.
How do I care for the product?
To clean the products, we recommend using a clean, damp, well-wrung cloth. Depending on the material, cleaning products may damage the product and alter its surface. We therefore recommend using plain lukewarm or warm water for cleaning.
What is 3M tape?
3M is an internationally recognized company known for its goal of making life easier and improving living standards through innovation and smart products. Its products include 3M tape, a quality-assured double-sided tape that provides reliable adhesion from the start.
Did you know that the soap dispenser holders come in three finishes?
We have both soap dispensers and soaps from Five Oceans and Meraki that fit perfectly in our soap dispenser holders. You can choose between matte black, stainless steel and chrome.
Retro
Country
Modern












